Launch one click update

When all that page has been downloaded at the bottom there is another next page down button for the next web page of manufactures.

Do the same and click down from 31 to 34 and save. Please note. The count of manufactures depend on the software you have purchased. When all of the manufactures have been downloaded please exit safely near the left hand top of the screen. However it is necessary to install the drivers on Windows 98 CD driver disks included in the kit with x Please click on the source folder browse icon to locate your desktop then find the x folder you created.

Then on the Launch update screen you should see all of the data and car manufactures in the top left hand side left click on select all. Once you have done that please click on the target folder browser icon to locate your USB CF data card reader. Locate the removable disc were the cf card is. Please check the hardware info. Note: Time to time you may receive a decompression error when trying to update. This is normal this fault is normally down to insufficient space on the cf memory card.

And the update will fail. You will have to delete some of the old updates in the card to resolve this problem. To delete the unwanted manufactures in the cf card please left click Icon in the bottom left of the screen. After this is done you can now repeat the update 33 again with the new date software yet again please wait…. Note: When this has happened please follow the cf card removal guide.

Other wise the date in the cf card will be lost. Procedure for pulling out the X CF card reader:. On the desktop of windows, open the window of my computer click the right mouse button on the removable disc to pop up a menu. Scroll down to eject in the menu.

Then pull out the cf card reader. Once done remove card from the card reader and place back into the side of the launch x then try on a vehicle. Download the new program by following here. If the above does not work for you then try the compressed zip version. If some manufacturers have initially failed, do not worry as the program will go back over them once it gets to the bottom of the list.

Please do not use the PC or surf the web whilst the software is being updated, it will corrupt and slow down the process.

If your memory card is low on free space it will not update, follow these instructions on clearing all data off the device by using your PC to format the drive. Updating your Launch scan tool has never been easier! Using our new One-Click update software, you can sit back and let your computer update your Launch diagnostics saving you time and money! You have now downloaded and installed the program. You should see a new icon on your PC desktop. Double click on this icon to open the program and update your equipment.

Now that you have installed the update tool and formatted your memory card you can start the update process following the below steps; If you have not inserted the USB card reader into your PC with a memory card you will see the below screen.

Otherwise it will automatically detect and go straight to the login screen. To update using this program you must have an active internet connection on your PC, as on the next stage the program will scan the server to see what is available in accordance with your subscription period.

This should not take long, please be patient whilst it is loading. Once the program has populated an update list it will show you what is available for updates. It is important not to surf the web or use your PC whilst the program updates as you will slow and corrupt the update process. If it starts failing and skipping a manufacturer or two leave it updating as it will automatically go back to the ones which have failed and reinstall those updates.

If it starts failing all the manufacturers then you do not have enough space on your memory card because you have not formatted it or your internet connection has gone down. Otherwise the program should continue updating the manufacturers one by one. If you are doing a complete update this may take minutes depending upon your internet connection and PC speed. If the program is only updating a few manufacturers for you then it will take much less time. Once updates are completed, press exit at the bottom right of the page to come out of the update tool.

Insert memory card back into Launch scan tool and power it up. On the start up procedure, it will say detecting noise do not press anything while this is starting up. When the 4 square dots appear in the middle of the screen you must press and hold for seconds with the stylus until it lights up, then, release the stylus, it will go to the bottom left corner and you press and hold again for seconds, lights up and release, do this for all corners and you have calibrated the screen.

Free download: X Easy Update Tool. In addition you can specify a minimum required version; that is, an update is installed if the user's version is lower than the required version.

You can configure the application to check for updates programmatically based on an event such as a user request. The procedure "To check for updates programmatically" in this topic shows how you would write code that uses the ApplicationDeployment class to check for updates based on an event. You can also deploy your application from one location and update it from another.

See the procedure "To specify a different update location. Update behavior is managed in the Application Updates dialog box, available from the Publish page of the Project Designer. With a project selected in Solution Explorer , on the Project menu, click Properties.

Click the Updates button to open the Application Updates dialog box. In the Application Updates dialog box, make sure that the The application should check for updates check box is selected.

In the Choose when the application should check for updates section, select Before the application starts. This ensures that users connected to the network always run the application with the latest updates. In the Application Updates dialog box, make sure that the check box The application should check for updates is selected. In the Choose when the application should check for updates section , select After the application starts.

The application will start more quickly this way, and then it will check for updates in the background, and only notify the user when an update is available. Once installed, updates will not take effect until the application is restarted.

In the Specify how frequently the application should check for updates section, select either Check every time the application runs the default or Check every and enter a number and time interval. Select the Specify a minimum required version for this application check box, and then enter Major , Minor , Build , and Revision numbers for the application. In the Application Updates dialog box, make sure that the The application should check for updates check box is cleared.

Optionally, you can select this check box to check for updates programmatically and also let the ClickOnce runtime check for updates automatically.